The Best Jeep Liberty Oem Double Din Dash Kit

Finally a Double Din Radio installation solution is in reach without having to pay tons of money for a custom handmade kit (these cost upwards of $349)!!! Installation Directions: 1. In the lower pocket area remove the one screw located in the center 2. Pry out on the factory bezel and separate it from the dash 3. Disconnect AC harness and the cigarette lighter 4. Remove the 4 Philip screws that hold the radio in place 5. Pull radio forward and disconnect the wire harness and antenna 6. Unmount the AC system from the factory bezel by removing the 4 Philip screws 7. Reattach that to the new double din bezel 8. Remove the old factory cigarette lighter and install on new double din bezel 9. Slide out the pocket liner and install on the new double din bezel 10. Remove radio supports by removing the 4 Philips (see picture gallery) 11. Use a drimmel or other plastic cutting device to remove the necessary plastic from the inside of the dash (see picture gallery) 12. Take the new bezel brackets and loosely attach to the new double din bezel 13. Dry fit your aftermarket double din radio into the bezel and remove/add any necessary trim rings/cages 14. Then line up aftermarket radio with the brackets and loosely screw through the brackets into the radio 15. Slide the aftermarket radio forward and back until you achieve a clean finish 16. Making sure the aftermarket radio is its square tighten all screws 17. Wire in the aftermarket radio to the aftermarket harness 18. Install antenna adapter 19. Reconnect the AC controls and lighter button with harnesses in the dash 20. Plug aftermarket wire harness into the factory radio harness. 21. Snap bezel into place and secure final screw in lower pocket area.

Finally a Double Din Radio installation solution is in reach without having to pay tons of money for a custom handmade kit (these cost upwards of $349)!!! Installation Directions: 1. In the lower pocket area remove the one screw located in the center 2. Pry out on the factory bezel and separate it from the dash 3. Disconnect AC harness and the cigarette lighter 4. Remove the 4 Philip screws that hold the radio in place 5. Pull radio forward and disconnect the wire harness and antenna 6. Unmount the AC system from the factory bezel by removing the 4 Philip screws 7. Reattach that to the new double din bezel 8. Remove the old factory cigarette lighter and install on new double din bezel 9. Slide out the pocket liner and install on the new double din bezel 10. Remove radio supports by removing the 4 Philips (see picture gallery) 11. Use a drimmel or other plastic cutting device to remove the necessary plastic from the inside of the dash (see picture gallery) 12. Take the new bezel brackets and loosely attach to the new double din bezel 13. Dry fit your aftermarket double din radio into the bezel and remove/add any necessary trim rings/cages 14. Then line up aftermarket radio with the brackets and loosely screw through the brackets into the radio 15. Slide the aftermarket radio forward and back until you achieve a clean finish 16. Making sure the aftermarket radio is its square tighten all screws 17. Wire in the aftermarket radio to the aftermarket harness 18. Install antenna adapter 19. Reconnect the AC controls and lighter button with harnesses in the dash 20. Plug aftermarket wire harness into the factory radio harness. 21. Snap bezel into place and secure final screw in lower pocket area.

Ram 1500- (2006-2008) Ram 2500- (2006-2009) Ram 3500- (2006-2010) Ram 4000- (2006-2009) Ram 4500- (2008-2010)

For nearly 40 years, Scosche has been producing quality built, affordable car stereo Dash Kits and Vehicle Wiring Harnesses. We know how you feel about your vehicle, your “pride and joy” and we will not design, engineer and deliver a replacement Dash Kit or Vehicle Harness that does not meet our extremely high standards. Whether you are looking for an exact fit and OEM color match of a Dash Kit or a replacement OEM Wiring Harness, Scosche has you covered.

Up until now installing an Aftermarket Double Din Radio into the 2005-2007 Jeep Grand Cherokee meant having to buy the factory navigation bezel ( $175 ), an aftermarket radio install dash kit ( $12 ), wiring harness and a antenna adapter ($6). However our new kit allows you to replace your Factory Radio with an aftermarket Double Din radio at a reasonable price with a cleaner look. We have taken the extra steps out for buying multiple parts and lowered the price plus you will get a better looking installed with our kit. This wire harness is compatible with standard wiring only. Will not work on models with Factory Infinity Systems, Boston Acoustic Systems or CAN Bus Radios (models REF, REC, RAQ or RAK; The radio’s name can be found on the face of the radio). Installation Directions- Tools needed for install – Philips screw driver, Dremel (rotary tool) and a Soldering Iron. You can buy a Soldering gun at Harbor freight for as low as $3.99 and a Dremel (rotary tool) knock off for $10.79 or just look on Amazon. Step 1: Gently pull on the factory bezel, it is only held on by a few plastic tabs up top and there are 2 clips on each side of the AC vents (totaling 4) and 1 clip at the bottom.. Step 2: You will see 4 Philips screws holding the factory radio in place, remove the screws and the radio will be lose and ready to come out.. Keep the screw for installation of new double din radio.. Step 3: Next unplug all the wire harness and antenna cable leading into the factory radio. You will now have the empty hole ready for new double din radio and your newly purchased dash kit (DO NOT DISCARD THE FACTORY BEZEL AS YOU WILL NEED THE AC VENTS TO PUT ON THE NEW BEZEL) Step 4: The removal of the AC vents from the factory bezel.

Double DIN Installation Dash Kit for Select 1990-Up GM Vehicles

The Install Centric ICCR6BN complete installation solution is an ideal choice for installing an aftermarket stereo into your 2007-14 Chrysler/Dodge/Jeep vehicles without altering the dash. Everything you need to perform a basic aftermarket stereo installation is included: the dash kit, wire harness, antenna adapter and wire connectors. The Double DIN dash kit includes a kit panel, a trim ring and brackets and is manufactured from high-grade ABS with precision tolerances so it delivers a gapless fit between the dash and the kit. The wire harness allows you to connect to the factory harness without cutting any wires. The ICCR6BN kit includes step by step instructions and colored coded wires for an easier installation.

Ram 1500- (2006-2008) Ram 2500- (2006-2009) Ram 3500- (2006-2010) Ram 4000- (2006-2009) Ram 4500- (2008-2010)

Metra 95-7333 Double DIN Installation Dash Kit for Select 2009-Up Hyundai Vehicles, Install dash kit for Double DIN/ISO Radios, Designed and manufactured with precision tolerances, resulting in a gapless fit between the dash and the kit, High-grade ABS plastic construction, Factory style texture. Kit Includes: Radio Housing Trim Plate and Radio Housing Brackets

Allows the installation of a 1/4 inch or 1/2 inch din equalizer with supports. Bolts directly to the factory radio mounting locations. High-grade ABS plastic construction. Allows the installation of a 1/4 inch or 1/2 inch din equalizer with supports. Bolts directly to the factory radio mounting locations. High-grade ABS plastic construction.